This is a TrueBend metal brake line replacement kit. All lines are supplied double-flared at each end with the special bubble flare for your VW. These malleable lines are easy to bend or coil without collapsing the tubing or restricting the flow of brake fluid.  Four couplers are included to join lines where necessary. Instructions are also included.

The average VW/Audi takes 26 feet of brake line to do the entire car,
 this kit has 40 feet of lines to fit all the various configurations.
Use the extra lines for another project!

this kit is for the following:

Audi

80 Series 1988 to 1992
90 Series, Quattro,1991 to 1993
200 Series 1989 to 1991
5000 Series, Quattro 1978 to 1988
A4 1996 to 1997
A6 1995 to 1997
A8 1997
S4 1992 to 1994
S6 1995
Coup 1981 to 1987
Fox 1973 to 1979 (see note below) 
Quattro 1983 to 1994
V8 1990 to 1993

 

VW
Beetle, Type 1 Karmann Ghia, Super Beetle 1958 to 1977
Cabriolet 1990 to 1997
Corrado 1990 to 1994
Dasher 1974 to 1981
Fox 1987 to 1993
Golf,GTI 1985 to 1997
Jetta 1980 to 1997
Passat 1990 to 1997
Quantum 1993 to 1988
Rabbit 1974 to 1984
Scirocco 1974 to 1989

Here is a list of what lines are included to do the models above

two 8 inch
one 12 inch
one 16 inch
one 20 inch
one 23 inch
one 27 inch 
one 30 inch
one 33 inch

two 40 inch
one 43 inch
one 47 inch
two 51 inch 

4 Unions to joint lines together

instructions for installation

A total of 20 lines and unions!!

Our TrueBend® brake lines resist corrosion, vibration, fatigue and shock from impact. They are coated for corrosion protection in compliance with GM132M-ASV and SAE J527B.  Each line is manufactured by double wrapping a copper coated steel strip to form a double wall tube.  Then, the tube is furnace brazed to fuse the copper/steel tube into one continuous and seamless tube.  The tube is then given a outer coat for corrosion and abrasion resistance. These lines are the strongest and safest avai; yet can still be easily bent without kinking or without damaging the  outer coat.

Some models come with a dual brake line system to the rear, this kit is for a single line system, you may be short a few lines if you have a dual system.  

This kit contains all the lines to do a wide variety of European cars, and many different configurations, so you will have unused lines in any installation. These extra lines are a bonus that can be used for other projects

The tubing is double walled, seamless and copper fused with a special inner and outer coating to provide protection from abrasion and corrosion. This is the same tubing that is used on new cars!

The lines are supplied straight.  If you need a very sharp bend next to the flare at the end of the line, you will need a bender listed under "tools/supplies" on our Ebay store.

All unions are solid brass to stop rust.

All lines are made in USA or Canada and are the stock 3/16" outer diameter with a factory flare.

Some 1973 to 1979 Fox models will need a adapter to 12x1 thread into the master cylinder

fits s the years: 58 1958 59 1959 60 1960 61 1961 62 1962 63 1963 64 1964 65 1965 66 1966 67 1967 68 1968 69 1969 70 1970 71 1971 72 1972 73 1973 74 1974 75 1975 76 1976 77 1977 78 1978 79 1979 80 1980 81 1981 82 1982 83 1983 84 1984 85 1985 86 1986 87 1987 88 1988 89 1989 90 1990 91 1991 92 1992 93 1993 94 1994 95 1995 96 1996 97 1997