Powered by Frooition Pro

Engine Water Pump ACDELCO PRO 252-202

Part Number: 252-202

Features:

  • All Makes water pumps fit GM vehicles as well as a wide range of non-GM vehicles
  • Thoroughly tested for reliable, leak-free performance
  • Coated seals support seal longevity and durability
  • Heat-treated shaft assemblies provide superior strength and durability over non-treated assemblies
  • High-quality bearings are permanently sealed and lubricated for greater durability and long life
  • Come with premium, high-quality replacement components needed for trouble-free and accurate installation
  • Uniform wall sections and smooth coolant-flow cavities for efficient and superior protection
  • Cast-iron or aluminum design, depending on vehicle application

Description:

An ACDelco Professional, premium aftermarket Engine Water Pump circulates coolant through your vehicles radiator and engine system to help maintain proper engine temperature and performance. The gaskets, seals, and O-rings packaged with this Professional, premium aftermarket water pump help guarantee that all necessary parts are available for trouble-free installation. ACDelco Professional Water Pumps are an ideal premium aftermarket replacement component for many vehicles on the road today. This water pump is manufactured to meet and exceed your expectations for fit, form, and function. This premium aftermarket replacement engine water pump is manufactured to meet or exceed your expectations for fit, form, and function.

Tips

Tips for Water Pump Inspection:
  • Clean all excess dirt and debris from the water pump housing.
  • Run your vehicle to increase engine temperature, and ensure the system is pressurized.
  • Inspect for leakage at the water pump outlet housing or the rear cover gasket, and leakage at the water pump vent or weep hole.
  • A stain around the weep hole is acceptable. However, if a weep occurs with the engine running and the coolant system pressurized, then the water pump should be replaced.
Tips for Water Pump Servicing & Installation:
  • Determine the root cause of failure, particularly if the water pump failed prematurely.
  • Clean and reinstall the coolant recovery reservoir before flushing the cooling system.
  • Flush the cooling system completely, using power flush equipment or thermal cycling the system with clean water three times. The most effective method of system flushing is to use a coolant exchanger, following the manufacturers operating instructions.
  • Do not use any non-approved flush agents, and replace the coolant according to manufacturers specifications.
  • Clean all sealing surfaces, and make sure all old gasket material is removed before installing your replacement component.
  • Never strike the water pump shaft, since this will damage the new water pump.
  • Torque all bolts according to the manufacturers specifications, and adjust belts to proper tension (if applicable) to manufacturers specifications.
  • Use sealant tabs only if recommended. Some sealant tabs or similar compounds may restrict coolant flow through the passages of some cooling systems.
  • With the new water pump installed, turn the hub by hand and check for rotation.
  • After installation, pressure-test the system for leaks and check for sufficient fan blade clearance between the blade and radiator shroud.
Tips to Help Prevent Water Pump Failure:
  • Flush your cooling system whenever the water pump or other system components are replaced. This will help prevent contamination from entering the system, which may result in repeated failure.
  • Utilize quality coolant when refilling your cooling system with the recommended 50/50 coolant/water mix. Distilled water should be used, as hard tap water can leave mineral deposits in the cooling system and reduce coolant flow, or result in corrosion and seal damage. Contaminated or depleted coolant can also result in corrosion and seal damage, and lead to pump failure. Take care to select the correct coolant for your vehicle by consulting the vehicle manufacturers service information.
  • Never overtighten your drive belts. Belts that are too tight may cause an overload on pump bearings, greatly reducing the life of the water pump.
  • Inspect the fan blade. If damage is not detected, bent blades, loose rivets, and cracks may result in premature bearing failure. If damage is found, do not try to repair the fanthe part should be replaced.
  • Ensure that your engine fan pulley (or clutch, if used) is seated properly on the pumps shaft. If the fan wobbles during rotation, vibration resulting in premature bearing wear may occur. Also check the fan clutch for wear and replace as necessary.
  • Inspect the thermostat and radiator cap. Examine your thermostat and radiator cap, and replace if they show signs of sticking or leaking.

FAQ

  • Can I use ACDelco Professional Water Pump Kits and Water Pumps on my non-GM vehicle?
  • Yes. ACDelco Professional Water Pump Kits and Water Pumps are for both GM and non-GM vehicle applications.
  • Do ACDelco Professional Water Pump Kits and Water Pumps come with installation components?
  • Yes. ACDelco Professional Water Pump Kits and Water Pumps are packaged with the gaskets, seals, and O-rings needed for installation.
  • Do all water pumps look the same?
  • No. Water pumps can vary greatly in size and appearance depending on the vehicle they are designed for.
  • Can a malfunctioning water pump harm my engine?
  • Yes. The water pump is responsible for moving coolant through your vehicles cooling system, keeping the heat generated by your engine at acceptable levels, and helping prevent overheating. A malfunctioning water pump can cause your engine to overheat, which may result in severe and costly engine damage.
  • Does the water pump affect the temperature inside the passenger compartment of my vehicle?
  • Yes. As part of regular cooling system operation, the water pump sends hot coolant to the heater core of your engine, which transfers heat into the passenger cabin of your vehicle. If this hot coolant is unable to reach the heater core, then this heat transfer cannot occur, and your passenger compartment remains colder than you want.
  • Does the water pump work when my vehicle is turned off?
  • No. Your vehicles water pump keeps coolant moving as long as the engine is running, and stops when the engine is turned off. If you want to be able to circulate coolant for a short time after the engine has been turned off, an auxiliary electric water pump is needed.

Troubleshooting

  • Leaking Coolant Puddles of coolant under your vehicle, a constant drip or stream of coolant from the water pumps weep hole, or a constantly empty or low coolant reservoir are all signs of potential water pump wear, and may be caused by cracks in the pump, or seal or gasket failures.
  • Engine Overheating If your vehicles engine overheats, it may not be receiving the required coolant flow. Make sure that your vehicles cooling system contains the proper level of coolant.
  • Rumbling Noise in the Pump A rumbling, squeaking, or screeching noise near the front of your vehicle when you start it may indicate a malfunctioning water pump bearing.
  • Visible Component Wear Worn seals, corrosion, cavitation/pitting of pump components, or a loose or wobbly pump shaft are all signs of wear that may lead to pump failure, and should be addressed.

Downloads

Warranty

Frooition www.frooition.com | eBay design, eBay store design, eBay shop design, eBay template design, eBay listing design
This listing is currently undergoing maintenance, we apologise for any inconvenience caused.