Find or Sell any Parts for Your Vehicle in USA

Draco Vs Kraken * Custom Boat Wrap - Customized To Fit Your Boat on 2040-parts.com

US $795.00
Location:

Naples, Florida, United States

Naples, Florida, United States
Condition:New Decal Type:Wrap Country/Region of Manufacture:United States

Phone (239) 431-7356 Monday-Friday 8am to 5pm (e.s.t)

Sold in directional pairs, one left and one right side.


This wrap purchase is for a boat wrap to fit on a boat that is between:
14 feet up to 19 feet in length

From the rubrail down to the waterline.**
Longer boats DO cost a more. Smaller boat sizes are fine as well.

We will customize the wrap AFTER purchase to fit the actual year, make and model of your specific boat to show the most available image area to achieve the best visual display.

Our boat wraps can be fitted to accommodate most boat models.

Once ordered and paid for, you will NEED to provide the
year, make, model, length of your boat and a side shot picture
as well as very accurate dimensions.

SEE EXAMPLE OF HOW TO MEASURE BELOW
Please email us with details.
Once you have approved the layout, we will manufacture it and ship within 36-48 hours. All products made on site.

Wrap will have excess in the front and rear as well as the top and bottom to allow for appropriate amount of trim.
Set up to be trimmed at the nose and a few inches around the back toward the motor.

Your graphics color may vary slightly from what you see depending 
on you monitor Setting.

(boat not included, ha!)
Material is 3M IJ180 cv3 cast boat wrap vinyl film with 3M 8518 cast overlaminate for maximum UV protection.
Shipping to the lower 48 U.S. only. No shipping to Hawaii and Alaska.

Kraken Boat wrap by Wrap Graphics

Please try to follow these instructions to ensure success.

1. Specify the color or design you prefer, such as “Green” or "Diver & Octopus".

2. Submit an image of the boat. Make it a nice side shot like this example.
Submit images and artwork to:
 artwork here

Skiff Example

3. Take some dimensions of the boat hull. Be sure to include the length along the rubrail,
the max depth from the rubrail down to the waterline edge where the wrap will end,
then along the hull every 2 feet or so as shown in the diagram.
Take Boat dimensions like this
4. Your wrap print will ALWAYS have more length and width than the actual dimensions
you send for “wiggle room” and proper trimming.

5. Be sure to include the year, make and model of your boat.

6. We submit a final mockup layout for your written approval showing the wrap you
chose superimposed on the image of your boat hull.

Mockup for proofing
7. Once we receive your approval the finished boat wrap is produced
and shipped within 36 to 48 hours.
YOUR WRAP WILL COME IN A RECTANGLE SHAPE AS SHOWN IN THE ABOVE
EXAMPLE. THIS ALLOWS FOR PLENTY OF TRIM AREA.

** 3b. If you want your boat wrap to go up over the rubrail into the gunwales, or if you want the bow or stern wrapped as well, you need to provide those dimensions as well. This will add to the cost. You can use the below diagram as a reference to ensure your wrap fits and presents itself the best.

Measure your boat similarly to this

Dimensions needed for rear of boat wrap

We have many variations of our graphics and also provide custom colors upon request.
 If you have any questions, Please don't hesitate to call.



One Lap of the Web: Car fails, electronic plates and 3D printing cars

Wed, 12 Jun 2013

We spend a lot of time on the Internet -- pretty much whenever we're not driving, writing about or working on cars. Since there's more out there than we'd ever be able to cover, here's our daily digest of car stuff on the Web you may not otherwise have heard about. -- The Porsche museum in Stuttgart, Germany contains the history and automobiles that have made the company what it is to this day.

Fiat-Chrysler to make Jeeps, Alfas in Italy starting in 2012

Fri, 26 Nov 2010

Fiat S.p.A. and Chrysler Group will build Alfa Romeo and Jeep models for global distribution as part of a new joint-venture company that will take control over Fiat's Mirafiori plant in Turin, Fiat said Friday. Fiat-Chrysler will invest more than 1 billion euros (more than $1.3 billion) to retool the factory.

Funky Kia Provo Concept arrives ahead of Geneva 2013

Sat, 02 Mar 2013

The Kia Provo Concept is heading to the 2013 Geneva Motor Show and looks to be half butch urban warrior and half coupe. (adsbygoogle=window.adsbygoogle||[]).push({});With the 2013 Geneva Motor Show looming we’re going to see plenty of reveals and leaks of new cars, concept cars and refreshed cars. Kia’s offering today comes in the ‘Concept’ category, but we hope it ends up in the ‘New Car’ category before long.