Mercedes Benz W100 600/600 Pullman Vehicle Jack Bilstein "mbmoaj" !!! Rare on 2040-parts.com
Brockton, Massachusetts, US
Mercedes Benz 600/600 Pullman Bilstein Jack "Mercedes Benz Mother Of All Jacks" This is an OE Bilstein mechanical jack standard issue with the W100 600/600 Pullman vehicles. It is a large and massive jack designed to easily lift the 6000+ pound vehicle. This jack is in fantastic nechanical condition operating smoothly all along its range of travel, it is not bent or otherwise damaged in any way. Cosmetically there are areas of missing paint and the resultant very light rusting of the bare steel, it will clean up very nicely and will look great after a repaint with the proper type paint. This jack does not come with an attached handle as the tire iron/lug wrench is used to raise and lower the mechanism. Included with this jack is the proper tire iron/lug wrench MB # 100 581 01 46 made in Germany by KLEIN This tool is in good condition, it's finish is missing in areas and there is surface rust, the shaft has a barely noticable slight bend apparently from loosening lug nuts.
Auction winner is required to make payment in full within 3 calendar days.
Shipping is available within the continental US for approximately $40, actual shipping expenses are the responsibility of the buyer. The winning bidder will only pay for the actual shipping cost; there is no charge for boxes, packing, handling, delivery, etc.
Shipping is possible world wide with prior agreement and arrangement. Securely and carefully packed this item's dimensions are 32" X 12" X4" X and weighs 20 lbs.
International bidders should contact this seller prior to placing bids, failure to do so can cause your bid to be deleted!
Other Parts for Sale
- 71 72 73 74 mopar b body charger roadrunner gtx rallye rally gauge lense nice (US $60.00)
- Nos oem genuine mopar 04606061 1997 dodge intrepid concorde oxygen sensor b4910(US $53.98)
- 1952 plymouth cranbrook rear fenders (pair)(US $150.00)
- Headliner trunk panel floor door insulation sound deadoner 4 feet by 6 feet roll(US $20.99)
- Chevy s10 15192485 fuel pump and rear light harness. from fuse block down frame(US $15.00)
- Gm door sill plate1992-96 blazer &1992-1996 c2500 nib (15980688)(US $7.00)
Lamborghini Veneno (2013) first official pictures
Mon, 04 Mar 2013Tomorrow McLaren will unveil its new McLaren P1, ditto Ferrari its Enzo successor, but on the eve of the 2013 Geneva motor show Lamborghini has just tried to trump the pair with the Veneno. The P1 is priced at £866k, the Ferrari will likely cost just as much, but you'll need £3m for a Veneno... £3m?!
Webinars: Listen again to Autodesk 'Automotive visualization, new quality standards in Virtual Prototyping'
Thu, 28 Mar 2013Autodesk presented its latest Webinar, 'Automotive visualization, new quality standards in Virtual Prototyping', on 11 April. Virtual Prototyping is one of the most important steps in the development of a new car allowing the evaluation of a prototype in different aspects before it's even built. Autodesk's new VRED product line can be used throughout the whole design and construction process on a single data basis, without the need to re-do work.
Bentley Arnage replacement to take on Rolls Royce
Sun, 12 Apr 2009Bentley's replacement for the Arnage in 2010 will go upmarket to compete with the Rolls Royce Phantom Bentley has revealed that after Arnage production finally ends in September it will be a full year before the replacement for the Arnage surfaces. Now the sceptics amongst us may put this down to the fact that Bentley are struggling to sell the cars they already make in the current climate, never mind producing an even more luxurious and expensive model. But Bentley say it’s so they can put a clear line under the current Arnage before its replacement arrives late in 2010.