Find or Sell any Parts for Your Vehicle in USA

On 3 Mustang Cobra Mach 1 4v Head Cooling Mod 2001 Coolant Upgrade Dohc Mach1 on 2040-parts.com

US $85.00
Location:

Westerville, Ohio, United States

Westerville, Ohio, United States
Condition:New Brand:ON 3 PERFORMANCE Manufacturer Part Number:CM

On 3 Performance

614-439-0057

 

99 – 04 Mustang Cobra / Mach 1 / 4v Head Cooling Mod

 

Brand New In The Box Product

Always Kept In Stock Ready To Ship

 

 

This is a brand new head cooling mod in the box and will allow you to install without pulling the transmission. Certain kits on the market cannot be installed without pulling the trans, you don’t even have to pull the supercharger on the 2003 / 2004 Mustang Cobras.  Very simple install by knocking out the back freeze plug on the back side of the driver-side head.  Tap the fitting into place and just bolt it down.  The aluminum tube supplied splices into the front coolant hose before going into the radiator.  All rubber hose is included to go from the back of the head to the supplied aluminum tube. Why spend $120+ to accomplish the same thing?  We have sold this kit for over 3 years now and run it on both of our street/race cars. 

 

Without the head cooling mod, there isn’t a cooling passage in the back of the head and believe to cause engine failure.  This will allow the coolant to just pass though the head and flow out of the back freeze plug port and directly back to the radiator.

 

We also have people question the 90 degree elbow talking about possible failure.  Its not standard plastic, the material is Delrin and actually a machined out piece.  If your not fimiliar this material is used in many industries, it has high strength, resistance to many chemicals including gasoline and resistant to continuous impact.  Ideally this was a good matieral choice and fit better than the brass hose fittings on the market.

This will not work on the 96-98 4v motors, they have the IMRC plates that interfere.  I do believe its possible if you have these deleted, you could run this if you have access to the freeze plug and hole for the hold down tab.

 

 

INCLUDED WITH THE KIT:

 

-         Head Coolant Fitting

-         Aluminum Coolant Tube

-         Coolant tubing / Delrin Block Fitting

-         Clamps For All Connections

 

Shipping:

Shipping is free to the lower 48 states, add $5 for AK and HI

 

Ohio Residence:

All Ohio sales are subject to 7.50% Ohio Sales Tax

Policy:

 

Products are brand new and included everything from the photo unless otherwise specified.  Buyer takes all responsibility for this product and the install of the product on the car regardless of any condition.  We will not be held liable for any damages or injury do to the install or use of this product.  If purchasing from out of the USA, we will only ship to verified Paypal members.  All sales are final unless otherwise specified in the auctions.  We always package the items sufficiently and use adequate packing material to prevent damage.  Unless insurance is purchased, the buyer will be responsible if the product is damaged during transit.  We ship UPS and USPS Internationally so if there was damage, you would want to file with the delivery driver if there was visible damage.  We are always willing to work with customers in order to keep satisfaction to a certain point.  As you will see we offer many products and are not going anywhere.  Buy with confidence and enjoy

 

 photo headcoolingkitphoto_zpsa08496b7.jpg  photo headcoolingkitphoto1_zps3f6f60e2.jpg  photo polishedheadcoolingtube2_zps55013834.jpg

 

Here are a few installed photos to show you how it works and how to install yours.  The freeze plug in the back of the driverside head will need to be knocked out.  Then you can install the main billet machined body that will allow you to port into the back of the head

 

 

 photo on3headcoolingmod5_zps8f4a1145.jpg  photo on3headcoolingmod4_zps40b7cdc2.jpg  photo on3headcoolingmod1_zps194dfcf8.jpg

Once you have that fitting installed into the head and the short hose and delrin elbow, you just run the line around that taps into the front radiator hose.  As you can see the install is very straight forward, very functional and a must on your 99+ 4v motor

 

 photo on3headcoolingmod7_zpsc1f6aeb9.jpg  photo on3headcoolingmod6_zps0bb24451.jpg  photo on3headcoolingmod_zpsc5d1620e.jpg

New Kia Carens teased

Wed, 25 Jul 2012

A new Kia Carens is being teased with a couple of design sketches ahead of a reveal at the Paris Motor Show. On sale Spring 2013. Kia like to call their Carens MPV ‘Stylish and Practical’.

BMW M5 30 Years Edition is OFFICIAL – it’s the ’30 Jahre M5′

Wed, 07 May 2014

The BMW M5 30 Jahre M5 (pictured_ celebrates 30 years of the M5 We revealed at the weekend that BMW were planning a special edition M5 to celebrate 30 years of the M5 and. as expected, BMW has now revealed the 30 Jahre M5 (30 years of the M5). As expected, the 30 year M5 gets a tweaked version of the 4.4 litre twin-turbo V8 found in the regular M5, but builds on the M5 Competition Package model by throwing an extra 25bhp in to the mix for a total of 592bhp (600PS).

Arash AF-8 (2008): first official pictures

Mon, 21 Jan 2008

By Ben Pulman First Official Pictures 21 January 2008 16:49 Arash Farboud, the man who created the car that spawned the Farbio GTS, has today announced details of his latest supercar venture, the AF-8. Priced at £120,000, the AF-8 is the baby brother to the AF-10 - a smaller, more user-friendly car than the hardcore hypercar. Though both cars will use the same GM-sourced 7.0-litre V8, the AF-10 will use a tweaked version with 550bhp, while the AF-8 will use the unit in standard Corvette Z06 tune.