Vinyl Film Tint 12" X 24" Headlight Taillight Fog Wrap Cover Gloss Purple on 2040-parts.com
广东, China
Description Features: 1 piece of Brand New, self-adhesive 12'' x 24"=(30x60cm) Self-Adhesive Selective Charming light smoke Vinyl Film Tint Wrap For Car Headlights Fog purple. This is the high quality yellow protection vinyl film sheet that you've been waiting for so long in glossy finishing for varieties of places such as headlights, tail lights, fog lights, side marker lights, bumpers, hood or even windshield. Fitment: Universal fit, even though the parts compatibility list only shows 300 vehicles, but this product will fit any cars, SUVs or trucks. You can use this vinyl film for any headlights, fog lights, sidemarker lights or even top part of the windshield, etc. Simply clean the surface and apply this high quality vinyl sheet to anything smooth surface and cut off the edge. It will not damage your lamp nor leave any residual These kits are universal they fit all makes and models. They are NOT Pre-Cut and are much easier to install then Pre-cuts. This kit is for 1 sheet 30" x 50". Additional kits may be required for complete coverage of two or more lights. Package: 1* 12'' x 24" purple Smoke Headlight Cover Sticker 2, easy installation, good viscosity, does not affect the original light source, waterproof sunscreen. 3, with a strong protective effect, scratch-resistant, durable. 4, the product environmental protection, not on the human body and the environment to produce toxic side effects and pollution. 5, suitable for DIY operation. Sticker paste operation instructions: Dry paste method】 【motorcycle stickers or small stickers apply 【Dry sticking method steps】 Use tools: clean rags, scraping, credit cards 1, clean the body paste position, conditions can be used without fiber off the cloth dipped in 50% of the Alcohol or isopropyl alcohol or acetone to scrub, but also with soapy water; the surface of the solvent to be cleaned After the solvent is completely evaporated, paste 2, the transfer film (paste in the reflective paste on the transparent film) together with the car stickers lifted; Case, the slow side of the paste, while scraped with a tool, while the end of paper to expose. 3, if the car sticker length and width are less than 10 cm, you can peel all the stickers and then paste. But must be careful , Do not accidentally stick or fall off the ground sticky dust. 4, with a clean rag or scraping [such as phone cards or credit cards] on the transfer film repeatedly wiping or scraping scraping A few; until there is no bubble inside the car stickers, and then torn [transparent] transfer film can be recommended 24 hours Do not exposure or car wash. 【Wet stickers】 car stickers or large car stickers apply [Recommended double operation] 【Wet sticker steps】 Use tools: watering can, clean rags, scraper, utility knives, hairdryer 1, will need to paste the surface clean in preparation for the paste before the glass water evenly spray on the need to paste Surface (after cleaning the car body, will be posted on the body parts with watering can) - mainly used to Reduce sticker viscosity, easy to adjust the position. 2, to determine the need to paste the location of the post, together with the car stickers from right to left to [or from top to bottom] lift a Side and with a cloth to its pressure on the car table, and then while the paste, while flattened with a rag, while exposing Bottom paper. 3, encountered a door handle or anti-collision of the material according to the circumstances cut open and included or loaded. 4, timely adjustment, the general location of the figure to determine correct, scraper with the scraper repeatedly water and air bubbles, When using the scraper from right to left oblique scraping. 5, case of the door and sewing with a utility knife are divided open, inward package affixed. 6, as far as possible in the car stickers in the water dry, conditional heating tube can be properly dried. Suggest: 24 hours as far as possible not exposure, 48 hours should not be washed. |
Headlight & Tail Light Covers for Sale
- Ford mustang tail light covers - fits 1993 mustang **look**(US $50.00)
- Trailer hitch wiring tow harness for subaru forester 2009 2010 2011 2012 2013(US $35.00)
- Draw-tite trailer hitch wiring tow harness for nissan nv200 2013 2014(US $56.00)
- Chrome side door handle bowl cover cup trim for honda vezel hr-v 2014 2015(US $18.55)
- B623-51-283 brand new genuine mazda oem license lamp cover rh (cover bombilla)(US $32.25)
- V tech 1550 slotted grill style tail light cover gm new(US $22.95)
General Motors says its EN-V concept might be tested in large cities
Wed, 12 Oct 2011General Motors is working on a second generation of its EN-V electric-car concept and might test the two-seat, pod-shaped vehicle in large cities around the world. The EN-V will wear the Chevrolet badge. It is designed to communicate with other vehicle and city infrastructure to minimize congestion.
Battery breakthrough set to accelerate electric-car development
Thu, 12 Mar 2009A team of scientists working at the Massachusetts Institute of Technology are claiming a significant breakthrough in recharging times for lithium-ion batteries. According to findings published in the scientific journal Nature, MIT researchers Byoungwoo Kang and Gerbrand Ceder have unlocked the potential of lithium-ion batteries by patenting a unique process which is claimed to allow a typical laptop power pack to be fully recharged in less than a minute--an improvement in recharging performance of roughly 90 percent over existing lithium-ion batteries. Lithium-ion batteries generate electric current via the flow of lithium ions across an electrolyte, from an electrode to a cathode.
Ford lines up Mark Fields to succeed Alan Mulally
Thu, 01 Nov 2012Ford Motor Co. has named Mark Fields its chief operating officer, putting him in line to succeed CEO Alan Mulally when he retires no sooner than the end of 2014. The appointment of Fields, 51, who has been president of Ford's Americas unit, was part of a sweeping overhaul of executive ranks unveiled Thursday.