Benson's 83mm Sleeved B18b1 Built Motor 800whp Ls Vtec Gsr B18c1 Evans-tuning on 2040-parts.com

This auction is for 1 Fully built long block from valve cover to oil pan, with NO accessories included. No manifolds, solenoid, no transmission, no clutch, no crank pully, no extra AN fitting or nothing except what is described.
This motor is fully built with ZERO miles on it. THIS MOTOR HAS NEVER BEEN STARTED. Every single part purchased was and is brand new, the only "used" parts are the head casting, block casting, oil pan and valve cover. The car never had a wire harness finished, the motor was NEVER ATTEMPTED TO START. I will not warranty this motor, as it is a high performance race motor, but I 100% guarantee this motor is as described. I will help in any way shape or form to prove this motor is exactly as described. You are more than welcome to come drop the oil pan, pull the valve cover, or drop a bore scope down the cylinder if you would like. I Will also bring the motor to any 3rd party shop of your preference if they are willing to look it over to vouch the condition. I live 10 minutes from the Evans-Tuning shop in Pennsylvania. This motor was never started, I never finished acquiring my fuel system, wire harness or tuning for the car and lost interest. 8 years later I decided it's time to move on. I have a binder with $22,000 in parts I invested into the car, well over $6000 is in this long block with head alone. Pictured is all my PayPal recipts and other recipts for the parts and assembly of this motor. I do have the oem parts recipts too, not pictured but I will include copies, as they are large orders and have more than just motor parts.
I do have the title to the car the motor (98 Ls b18b1) came from and will include it with purchase of the motor.

This motor was Sleeved in 2010 and assembled by Jeff at Evans-Tuning. It then sat, holes taped up, and saran wrapped, blanketed in a clean room of my house until 2015 when I pulled it out to install it into my car pictured. After realizing how much I had invested and how far I needed to go, I decided it was time to move on. The motor has the following parts, all name brand parts or OEM honda. If a bolt was taken out, 90% were replaced with brand new OEM hardware.

Head is a p72 GSR VTEC head with Laskey Racing Stage 2 build. Laskey racing sends the Heads to Portflow who assembles it.
P72 Head
Super tech stainless steel valves
Super tech dual valve springs
Super tech ti retainers
Hot tanked, followed by a 3 angle valve job, surface and new valve seals.
Golden Eagle 83mm LS/VTEC Conversion with OEM bored headgasket and ARP head studs
SKUNK2 Tuner 2 Vtec Cams
BDL Adjustable cam gears
OEM GSR valve cover with 4 -10 bungs TIG welded by Evans-Tuning secured with SKUNK2 flush hardware
Valve cover is powder coated Red Vein by Kings Coatings in Allentown Pa.
OEM Timing belt

Bottom end started as a stock b18b1 with 120k on it when it was sent to Laskey Racing, who sends it to Dan Benson at Benson's Racing. The sleeves are 83mm set to the tolerances for the CP SC7012 Pistons used which is a 9.0:1 vtec piston, although with the LS Eagle rods used the it is slightly higher. Once Laskey racing sent the block back, I took it to Jeff at Evans Tuning who finished assembling the motor.
83mm Benson Sleeved block
Benson's balanced and micropolished LS crankshaft
CP SC7012 Pistons
Eagle LS rods with ARP hardware
OEM Integra oil pump
OEM Integra water pump
OEM Oil pan with PassWord JDM baffle tig welded in, -10 oil return bung welded powder coated Wrinkle black by Kings Coatings in Allentown Pa.
ACL Bearings

This motor was built for my car which was intended to run 600 - 800whp with the fuel system and turbo that I had.

I will deliver this motor for FREE within 400 miles one way of zip code 18013 if the buy it now is used. I will help deliver it further if need be for a negotiated fee. I will need $500 non refundable PayPal deposit prior to delivering the motor and cash remainder before releasing.

Any questions, please feel free to ask and I can provide my cell phone number.

I will gladly split the head from the bottom end at request. I would need full payment for either item before doing so.

CASH IN PERSON ALWAYS GETS A BETTER DEAL!!!!!!!!!!!!!!!!!! I have to add the 3.4 % paypal fee and the 10 % selling fee into the list price of this ad. Please keep this in mind when "Making an Offer".

************PARTIAL PAYPAL PAYMENT ONLY. I will NOT ACCEPT FULL PAYMENT IN PAYPAL due to the fact that EBAY holds sellers funds for 21 days.************