Find or Sell any Parts for Your Vehicle in USA

Crysis Spiral Boat Wrap - Customized For Your Boat on 2040-parts.com

US $595.00
Location:

Naples, Florida, United States

Naples, Florida, United States
Condition:New Decal Type:Wrap Country/Region of Manufacture:United States

 

Phone (239) 431-7356 Monday-Friday 8am to 5pm (e.s.t)

Sold in directional pairs, one left and one right side.
This wrap purchase is for a boat wrap to fit on a boat that is between 18 feet to 20 feet in length
From the rubrail down to the waterline.**

Longer boats may cost a little more.
Smaller boat sizes are fine as well.

We will customize the wrap AFTER purchase to fit the actual year, make and model of your specific boat
to show the most available image area to achieve the best visual display.

Our boat wraps can be fitted to accommodate most boat models.

Once ordered and paid for, you will NEED to provide the
year, make, model, length of your boat and a side shot picture
as well as very accurate dimensions.

SEE EXAMPLE OF HOW TO MEASURE BELOW
Please email us with details.
Once you have approved the layout, we will manufacture it and ship within 36-48 hours. All products made on site.

Wrap will have excess in the front and rear as well as the top and bottom to allow for appropriate amount of trim.
Set up to be trimmed at the nose and a few inches around the back toward the motor.

Your graphics color may vary slightly from what you see depending 
on you monitor Setting.

(boat not included, ha!)
Material is 3M IJ180 cv3 cast boat wrap vinyl film with 3M 8518 cast overlaminate for maximum UV protection.
Shipping to the lower 48 U.S. only. No shipping to Hawaii and Alaska.

Boat wrap by Wrap Graphics

Please try to follow these instructions to ensure success.

1. Specify the color or design you prefer, such as “Green” or "Diver & Octopus".

2. Submit an image of the boat. Make it a nice side shot like this example.
Submit images and artwork to:
 artwork here

Skiff Example

3. Take some dimensions of the boat hull. Be sure to include the length along the rubrail,
the max depth from the rubrail down to the waterline edge where the wrap will end,
then along the hull every 2 feet or so as shown in the diagram.
Take Boat dimensions like this
4. Your wrap print will ALWAYS have more length and width than the actual dimensions
you send for “wiggle room” and proper trimming.

5. Be sure to include the year, make and model of your boat.

6. We submit a final mockup layout for your written approval showing the wrap you
chose superimposed on the image of your boat hull.

Mockup for proofing
7. Once we receive your approval the finished boat wrap is produced
and shipped within 36 to 48 hours.
YOUR WRAP WILL COME IN A RECTANGLE SHAPE AS SHOWN IN THE ABOVE
EXAMPLE. THIS ALLOWS FOR PLENTY OF TRIM AREA.

** 3b. If you want your boat wrap to go up over the rubrail into the gunwales, or if you want the bow or stern wrapped as well, you need to provide those dimensions as well. This will add to the cost. You can use the below diagram as a reference to ensure your wrap fits and presents itself the best.

Measure your boat similarly to this

Dimensions needed for rear of boat wrap

We have many variations of our graphics and also provide custom colors upon request.
 If you have any questions, Please don't hesitate to call.



Audi R8 GT Spyder arrives

Fri, 03 Jun 2011

Audi R8 GT Spyder - a mere £200k You didn’t think that Audi – Kings of the niche-fill – would settle for producing just 333 tin-top Audi R8 GT, did you? Of course not, so you’ve been expecting the next instalment in the race to make the most expensive Audi, and here it is – the Audi R8 GT Spyder. Just as it was with the R8 GT Coupe, the R8 GT Spyder will be limited to just 333 cars and all of those will come in LHD, even though Audi expect 30 to be sold in the UK.

Tribute to Briton killed in crash

Tue, 15 Oct 2013

THE GOVERNING BODY for UK motor sports has paid tribute to a "hugely promising" young British driver killed in a crash. Sean Edwards was a passenger in a Porsche when it reportedly hit the barriers at Queensland Raceway in Willowbank, west of Brisbane, Australia, during a private test session. The driver, a 20-year-old man from Brisbane, was pulled from the burning wreckage and is in intensive care with life-threatening injuries.

Spies given licence to speed

Mon, 13 Jan 2014

Secret agents are to be given the right to speed when behind the wheel, under changes of the law expected to be announced today. Currently, MI5 and MI6 officers have to stick to the rules of the road, even when national security is under threat. On Bing: see pictures of James Bond Find out how much a used Aston Martin costs on Auto Trader However, new plans to be announced by transport minister Robert Goodwill will give spies the same exemptions as emergency services.