Find or Sell any Parts for Your Vehicle in USA

Td05 16g Td05h 4g63 Dsm .70 A/r 360+hp Turbo Charger+wastegate+boost Controller on 2040-parts.com

US $188.98
Location:

Rowland Heights, California, United States

Rowland Heights, California, United States
Condition:New Brand:Speed Daddy Compressor Trim:50 Manufacturer Part Number:TBCTD05H16G+BCRD Hatchback Exhaust (Downpipe) Flange:Standard Mit TD05 DSM 16G 4-Bolt Other Part Number:Convertible Exhaust (Turbo Manifold) Flange:Standard TD05 4-Bolt Placement on Vehicle:Front, Rear, Left, Right Turbine A/R:.70 Surface Finish:Cast Turbine Trim:77 Color:Metallic Instruction Included:No Materials:Cast Iron/Steel Turbo Housing/ Aluminum Controller Turbine Inducer / Exducer (mm):56.12 / 49.38 Compressor A/R:.49 Intake Inlet/ Outlet:2.250" & 1.375" Compressor Inducer /Exducer (MM):48.20 / 67.90 UPC:DOES NOT APPLY

Categories
Newsletter
Add my Store to your Favorites and receive my email newsletters about new items and special promotions!

General Interest
We Accept
TD05 16G TD05H 4G63 DSM .70 A/R 360+HP TURBO CHARGER+WASTEGATE+BOOST CONTROLLER
Description
High Compression/ Boosting Turbocharger:

The objective of a turbocharger is to improve the engine's volumetric efficiency by solving the amount of air flow into the combustion chamber limitation. This ultimately results in an increased torque and output of the engine. A naturally aspirated automobile engine uses only the downward stroke of a piston to create an area of low pressure in order to draw air into the cylinder through the intake valves. The pressure in the atmosphere is about 1 atm (approximately 14.7 PSI),so there ultimately will be a limit to the pressure difference across the intake valves. This will also limit the amount of airflow entering the combustion chamber. Since the turbocharger increases the pressure at the point where air is entering the cylinder, a greater mass of air (oxygen) will be forced in as the inlet manifold pressure increases. The additional air/oxygen flow makes it possible to maintain the combustion chamber pressure and fuel/air load even at high engine revolution speeds, increasing the power and torque output of the engine.

30psi Turbo Boost Controller:

A manual boost controller is a simple mechanical and pneumatic control to allow some pressure from the wastegate actuator to escape or bleed out to the atmosphere or back into the intake system. This can be as simple as a T-fitting on the boost control line near the actuator with a small bleeder screw. The screw can be turned out to varying degrees to allow air to bleed out of the system, relieving pressure on the wastegate actuator, thus increasing boost levels. These devices are popular due to their negligible cost compared to other devices that may offer the same power increase.

Specifics and Features:

  • Capable of Boosting Horse Power up to 300+ BHP
  • Minimum Estimated Power Gain: 75 - 100 HP
  • 20psi Efficient Torque Turbocharger
  • High Quality Material, Cast Housing with Durable Steel

    Exhaust (Turbo Manifold) Flange: Standard TD05 4-Bolt
    Exhaust (Downpipe) Flange: Standard Mit TD05 DSM 16G 4-Bolt
    Intake Inlet/ Outlet: 2.250" & 1.375"

      Compressor:
      Trim: 50
      A/R: .49
      Inducer/ Exducer (mm): 48.20 / 67.90
      Turbine:
      Trim: 77
      A/R: .70
      Inducer: 56.12 / 49.38
  • Includes:

  • 1 x Turbocharger Kit
  • 1 x Turbo Boost Controller
  • Hardware as Shown in the Picture Above
  • Notes:

  • 100% Brand New
  • Professional Installation is Highly Recommended
  • Installation Instruction is NOT Included
  • Related Products

    DOMESTIC LOWER 48 US STATES: FREE

    SALES TAX: CA ONLY


    VERY IMPORTANT:
    Double check shipping address. We are not responsible for incorrect or undeliverable addresses.

    Please use Shipping & Payments tab on top of page for shipping details for your location.

    Shipping to PR, HI, AK and PO Box addresses will be charged the same as shipping to Canada. GU, VI, SAIPAN will be charged the same as international shipping rate.

    For Canada shipping please select the lowest price. We do not offer expedited shipping.

    US Territories such as GU, VI, SAIPAN will be charged the same as international shipping rate. Transaction will be held until a full shipping amount received.

    Some of the packages cannot be delivered to a PO Box. Customer is responsible to ensure PO Box address given is deliverable by the shipping company. Package will be held until a valid physical address is provided.

    Customer assumes shipping charges incurred in shipping to undeliverable address.

    International buyers are responsible for all customs duties, taxes, and other applicable fees incurred by the country's customs/border regulations. Please contact customs for more information.

    We ship 98% of all orders the same or next business day after payment received/cleared. Please understand that once orders are shipped, we cannot control the transit times thereafter. Most orders will ship via USPS First Class/Priority Mail or FedEx/UPS or the best suitable carrier for the specific size of the product.

    We are not responsible for any changes to address after item has been shipped.

    Turbo Chargers for Sale

    2014 Hyundai Genesis first glimpse

    Thu, 24 Oct 2013

    Here are the first official shots of the next Hyundai Genesis, a long, cool drink of water that will chart the course for many larger Hyundai sedans to come. “We want more premium luxury,” said Moon Sik Kwon, president of Hyundai R&D. “Genesis will lead the way.” Details are not officially released yet, so, even though we just drove the thing all over Hyundai's Nam Yang proving ground here in Korea and have a definite opinion about it, we can't tell you whether or not it was a well-composed, powerfully quick, huge step up and over the first Genesis sedan.

    BMW Project i – Isetta revived?

    Wed, 05 Aug 2009

    Does the Isetta video from the BMW Museum give a clue to BMW's 'Sub Brand' for its Project i City Cars? It now seems that this is getting closer to reality, as BMW has let it be known that the range of small city cars they are working on as part of the ‘BMW Project i’ will be launched as a ‘Sub Brand’. But what does that mean?

    Bristol Cars goes Bust

    Fri, 04 Mar 2011

    Bristol Fighter - Bristol Cars are in Administration I know, you didn’t even know they still existed. They do, but for how much longer is anyone’s guess as Bristol Cars calls in the administrators. Which is a real shame; a proper, eccentric British car maker finding it impossible to make enough sales to pay the bills, when there seem to be enough batty billionaires to buy the worst atrocities the world’s pimpers can muster (much the same problem afflicted Overfinch).