Find Wave Cutter Custom Boat Wrap - Customized to fit your boat in Naples, Florida, United States, for US $595.00

Condition:New Decal Type:Wrap Country/Region of Manufacture:United States

Sold in directional pairs, one left and one right side.
This wrap purchase is for a boat wrap to fit on a boat that is between 18 feet to 20 feet in length
From the rubrail down to the waterline.**
Longer boats may cost a little more. Smaller boat sizes are fine as well.

We will customize the wrap AFTER purchase to fit the actual year, make and model of your specific boat to show the most available image area to achieve the best visual display.

Our boat wraps can be fitted to accommodate most boat models.

Once ordered and paid for, you will NEED to provide the
year, make, model, length of your boat and a side shot picture
as well as very accurate dimensions.
SEE EXAMPLE OF HOW TO MEASURE BELOW
Please email us with details.
Once you have approved the layout, we will manufacture it and ship within 36-48 hours. All products made on site.

Wrap will have excess in the front and rear as well as the top and bottom to allow for appropriate amount of trim.
Set up to be trimmed at the nose and a few inches around the back toward the motor.

Your graphics color may vary slightly from what you see depending

on you monitor Setting.

(boat not included, ha!)
Material is 3M IJ180 cv3 cast boat wrap vinyl film with 3M 8518 cast overlaminate for maximum UV protection.
Shipping to the lower 48 U.S. only. No shipping to Hawaii and Alaska.

Boat wrap by Wrap Graphics

Please try to follow these instructions to ensure success.

1. Specify the color or design you prefer, such as “Green” or "Diver & Octopus".

2. Submit an image of the boat. Make it a nice side shot like this example.
Submit images and artwork to:

3. Take some dimensions of the boat hull. Be sure to include the length along the rubrail,
the max depth from the rubrail down to the waterline edge where the wrap will end,
then along the hull every 2 feet or so as shown in the diagram.
Take Boat dimensions like this
4. Your wrap print will ALWAYS have more length and width than the actual dimensions
you send for “wiggle room” and proper trimming.

5. Be sure to include the year, make and model of your boat.

6. We submit a final mockup layout for your written approval showing the wrap you
chose superimposed on the image of your boat hull.

Payment types: Visa, MasterCard, AmEx

Pay by Phone (239) 431-7356 Monday-Friday 8am to 5pm (e.s.t)
We can also process payments using paypal

7. Once we receive your approval the finished boat wrap is produced
and shipped within 36 to 48 hours.
YOUR WRAP WILL COME IN A RECTANGLE SHAPE AS SHOWN IN THE ABOVE
EXAMPLE. THIS ALLOWS FOR PLENTY OF TRIM AREA.

** 3b. If you want your boat wrap to go up over the rubrail into the gunwales, or if you want the bow or stern wrapped as well, you need to provide those dimensions as well. This will add to the cost. You can use the below diagram as a reference to ensure your wrap fits and presents itself the best.

We have many variations of our graphics and also provide custom colors upon request.
If you have any questions, Please don't hesitate to call.

Ford Model T climbs Ben Nevis: Ford Heritage Images

Wed, 05 Jan 2011

Ford Model T climbs Ben Nevis in 1911 (click for full size image) When the good Mr Clarkson decided Top Gear should do a piece about a Land Rover Discovery using its incredible off-road abilities to climb a mountain in Scotland we were all astonished that – despite a couple of hiccups on the way – he managed to get one of Land Rover’s finest up a mountain where cars were never designed to go. What’s even more astonishing is that Ford managed to do the same 100 years go, but they used a standard Model T and choose Britain’s tallest mountain – Ben Nevis – for the stunt. The 20 horsepower Model T was driven up Ben Nevis as a publicity stunt for Ford’s agent in Edinburgh.

New British car company coming?

Fri, 17 Jan 2014

British entrepreneur David Brown, not to be confused with the late Aston Martin owner Sir David Brown or the former British Prime Minister, has announced the upcoming debut of a new luxury sports-car brand bearing his name. Brown has teamed up with ex-Land Rover chief designer Alan Mobberley to create the new car, dubbed "Project Judi" for now. This wouldn't be an update of any existing model but rather an all-new exterior and interior design.

Porsche Macan caught on video

Wed, 01 Aug 2012

The Porsche Macan – a Porsche Cayenne on a boil wash – has been spied out testing and caught on video. We’ve seen spy photos of the Porsche Macan before – Porsche’s take on the Audi Q5 – and they look more like a cut down Cayenne being used as a mule for the Macan’s underpinnings than an actual Macan. But it seems that the shots so far are actually the Macan as it’s heading for production, which means Porsche has, perhaps unsurprisingly, chosen the 911 school of car design as its inspiration for the Macan and just stuck a Cayenne on a boil wash.

Wave Cutter Custom Boat Wrap - Customized To Fit Your Boat on 2040-parts.com

Decals for Sale

Ford Model T climbs Ben Nevis: Ford Heritage Images

New British car company coming?

Porsche Macan caught on video