Lot Of Kent Moore Piston Compressors - Pinion Gauge - & Sir Load Tool on 2040-parts.com
Tonawanda, New York, US
BIG LOT OF
KENT MOORE
TRANSMISSION TOOLS
THESE CAME FROM A CLOSED CHEVROLET BUICK HUMMER DEALERSHIP AND ARE IN NEW CONDITION:
EN-47701
Tool Number: | EN-47701 |
Superceded Tool Number: | J-8037 |
Tool Name: | Piston ring compressor |
Applications: | Line engine |
EN-47701 allows for greatly improved piston installation into the cylinder block through a unique design that compresses the rings during installation of piston at a controlled rate and will not cause the piston to bind in the compressor. |
EN-47836
Tool Number: | EN-47836 |
Price (USD): | $244.75 |
Tool Name: | PISTON RING COMPRESSOR |
Applications: | 2006-UP G6, ION, COBALT, SOLSTICE, HHR, SKY, 2.4L engine |
EN-47836 is a conical ring compressor used to guide the piston into the cylinder sleeve during piston installation. Due to the tight clearance between the piston and the cylinder wall, commercially available band-style compressors cannot be used, because they have a very high probability of scratching the piston or damaging the rings. |
EN-48260
Tool Number: | EN-48260 |
Price (USD): | $199.14 |
Tool Name: | PISTON RING COMPRESSOR |
Applications: | 2007-2012 Chevrolet Colorado, GMC Canyon, HUMMER H3 with 2.9L Inline 4 or 3.7L Inline 5 engine |
EN-48260 is a conical ring compressor used to guide the piston into the cylinder sleeve during piston installation. Due to the tight clearance between the piston and the cylinder wall, commercially available band-style compressors cannot be used, because they have a very high probability of scratching the piston or damaging the rings |
J-33838
Tool Number: | J-33838 |
Price (USD): | $1,089.67 |
Tool Name: | Pinion Shim Selector |
Applications: | 1998 S/T TRUCK |
Pinion shim selection is crucial during axle overhaul to achieve satisfactory axle life and operation. J-33838 is used on the new 7.25" front axle to select the correct pinion shim for desired axle operation. J-33838 and the pinion bearings are assembled into the axle. The arm for J-33838 is placed into the carrier side bearing bore. Previously essential J-29763 is installed and zeroed on the lowest point. The gauge arm is removed, and the reading indicated on the dial is the needed shim. |
J-38715
Tool Number: | J-38715 |
Price (USD): | $345.96 |
Tool Name: | SIR LOAD DEVICE |
Applications: | DR & PASS SIR SYS. |
ALL DRIVER/PASSENGER SIR Some 1992 models will feature both passenger and driver side inflatable restraint systems. This system will require J 38715 to simulate the electrical characteristics of the system during diagnostics. The main components of the tool are; circuits for inflator simulation on each side, a column simulation circuit, and a connector body for opening the shorting bar at the (derm) harness. The tool is packaged in a plastic storage case. |
PATIO LOT 5
Hammers, Pullers, & Extractors for Sale
- Vintage blue point 2oz ball peen hammer snap on handle auto body machinist tool(US $19.99)
- Mac impact driver 13 piece set(US $34.99)
- Vintage ken tool bead breaking hammer duck bill w/rubber,auto car truck tire(US $39.99)
- 2in1 professional harmonic balance puller set tools steering wheel crankshaft (US $19.70)
- Matco tools ft93fbb double flaring tool kit in a case (US $0.99)
- Snap on tools ppc270ak 27 piece punch and chisel set and vinyl carry pouch(US $0.99)
Susie Wolff ready to make F1 history
Thu, 03 Jul 2014SUSIE WOLFF is ready to make Formula One history on Friday, although is eager to play down its apparent significance. It has been 22 years since a woman took part in a grand prix weekend, with Italian Giovanna Amati failing to qualify in the opening three races of the 1992 campaign in a woeful Brabham before being replaced by a promising young Briton at the time - Damon Hill. On Friday, in her role as Williams development driver, 31-year-old Wolff will compete in Friday's first practice session for the British Grand Prix at Silverstone, taking over the wheel from Valtteri Bottas.
Ghosn says Infiniti quality must improve to build sales
Mon, 20 May 2013The boss says quality is key to Infiniti's future. After years with Infiniti at the back of the premium pack, Carlos Ghosn, CEO of Infiniti's parent, Nissan Motor Co., has ordered his team to nail quality once and for all as part of a push to catapult Infiniti into the top three brands of the premium market. Buoyed by a favorable dollar-yen rate and an ambitious new top executive, Infiniti might have its best chance yet to crack those ranks.
XCar talks to Chuck (Morgan) about the Morgan AeroMax
Tue, 12 Mar 2013Auto enthusiast YouTube channel XCar recently interviewed Charles Morgan, managing director of Morgan Motor Company, about the British car company, its AeroMax coupe and “automotive theater.” Morgan joined the family business in 1985. His father ran the company before him and his father, Henry Frederick Stanley Morgan founded the company in 1910. Morgan says he thinks that the Aeromax -- which happens to be his daily driver -- is one of the most beautiful cars in the world.