Mercruiser Type 1 Mc 1 Gimbal Gimble Housing Transom on 2040-parts.com

àType 1 Gimbal Plateß

 

This sale is for 1 Type gimbal plate!

Type 1 plates all have a round needle bearing for the steering shaft arm area not a bushing. Type 1’s run from 1965 to the about the end of 1975.

Plates are all in good useable or excellent condition and the price reflects just that!

 

This is for what I call a second, not perfect either a bad paint job or minor pitting for $250. I also have firsts/mint condition for $325 in another listing

 

Type 1 plates are different then anything newer then 1975 because the trim sensors on a type 1 are on the top of the gimbal ring and the newer models the trim sensors are on each side of the ring and the plates have bump outs on the sides for the trim sensors. If you notice these plates are flat where they go over the hinge pins to attach the bell to the ring. These plates are for the bell/ring combo that uses nails to hold slider pins in place to attach the bell to the ring.

 

This plate will include

 

1)   The water inlet tube with grommet 2 bolts and Grommet cover plate! So damages don’t occur in shipping the tube will not be installed.

2)   The 2 studs for the back of the plate that mount above the bearing area. These may or may not be installed.

3)   The 2 studs, nuts & washers for the bottom of the plate to mount the hydraulic divider block.

4)   A used grease seal is included (good and useable)

 

I do not include bellows, transom seals and such items as some customers already have bought them but I have them for you at a discounted price.

 

Once you buy reconditioned parts from me the discounts are as follows, And it is usually recommended to replace the following items as well.

 

Bellows sets with gimbal bearing, 2 universals and outdrive gasket are $100

 

Outer transom seal $10

 

Steering shaft seal    $20

 

Exhaust seal      $10

 

New trim sensors Port and Starboard $75 per set

 

New shift cable $50

 

The gimbal bearings are removed and all bellows surfaces are good. I deburr the plates in a deburring machine with soap, water & 1/4'” soft ceramic media to remove algae and loose paint. Every bolt & grease fitting hole I put bolts in to stop the media from getting into the hole so I know all threads are good.

 

Also check the pictures for your exhaust pattern, it can be 3 or a 5 bolt pattern. I have several of each type so when you buy let me know. You can save the pictures to your computer and zoom in to read the writing. Some of the type 1 styles have the hydraulic lines come out the sides and some out the bottom of the plate. Also some of the type 1’s use just hydraulic rams and some use a combination of hydraulic rams and 6” shocks. There is also 3 hydraulic rams setups for these so the best bet is to call so I can be sure you get the right plate the first time!

 

95% of my stock come from upstate NY, Ohio, Kansas & Illinois so fresh water but the truth is I have seen more damage from hard fresh water then from salt water.

 

This is not actual pictures and I do not send actual pictures!

I sell so many parts that trying to keep a posted picture is impossible and if you asked for a picture and paid for it an hour later the part might have already been packed for some one else. So please don’t ask for pictures.

 

Shipping is free in the continental US all other must ask for shipping quote! The weight packed for 1 plate is about 15 Pounds and I ship USPS Priority mail only. My zip code is 37096.

 

I Started this business Mikes Alphas to give people an honest place to get the right part the first time for a fair price. Check my feed back over 1000 strong and climbing. Ebay is about one third of my sales. To make it easy my email address is Removed (new eBay Policy) Look at my feedback and you will find my email address. my phone number is 931-589-2352 and my mailing/shipping address is,

Michael DeSeve

4391 Cedar Creek Road

Linden Tennessee 37096

Payment methods accepted are

Paypal Preferred

Visa / MasterCard

Discover

American Express

Receive payment upon pickup

I also accept credit cards over the phone if you don’t have an online payment method. Oh I also except Snail Mail!

Oh by the way tech support is free even if you don’t buy from me!

 

 

International Buyers  

Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyer's responsibility. Please check with your country's customs office to determine what these additional costs will be prior to bidding or buying. These customs/duty charges are different for all different countries and sometimes it is not applied. You should always consider they will be implemented so you are prepared. I ship everything internationally USPS postal service and I have no idea how it will arrive in your country. Please do NOT ask me to ship as gift or send a lower invoice amount, If you can’t afford your countries duty/customs fees please don’t buy from me. It is illegal for me to ship a paid for item as a gift and I will not lie for anyone and state a lower price.

 

Please leave us an all 5 star seller rating!  If for any reason you feel that you cannot leave us all 5's please contact us and we will do our best to help you resolve any problem!